Page Comparison

Zone RGB LED lights need to be paired to the iZone Bridge (COCB) to enable them to be controlled

Pairing can be done via the touch screen or the iZone Home App

Once paired a light can be grouped to other lights, switches, modules or they can be added to a Recipe for simple control logic

Pairing modules and switches is usually done manually by pressing the pairing button and at the same time pressing the pair button on the screen or app

1️⃣ Facia: 3 facia colours are available (White, Silver, Black)

2️⃣ Spring clips: Strong spring clips with rubber boots

3️⃣ Diffuser: Plastic diffuser

4️⃣ Aluminium body: The aluminium body is extremely durable and the cooling fins ensure the down light does not over heat and damage the electronics

5️⃣ Antenna: A small antenna protrudes from the casing for wireless communications (Not shown in this image)

Model numbers	CL5DB, CL5DS, and CL5DW
Certification	AS/NZS 60598.2.2;  AS/NZS 61347.2.13;  C Tick  N29007;  IP44;  IC-4; SAA
Power supply	Input: 220 - 240VAC 66mA ~ 50Hz
Connection	2 Pin Australian GPO plug
Transformer	Custom transformer included.  Output: 25V DC ~ 280mA The driver supplied is SELV EQUIVALENT
Power lead	1.2 meters
Power consumption	Maximum  9.0 Watts on full brightness (Cool white) Minimum 0.22 Watts in standby mode
Brightness	Maximum 523.7 Lumens
Efficiency	36.5 Lumens / Watt (Cool White)
Beam Angle	88.9
Control frequency	433 MHz
Operating Temperature	-20oC to +50oC
Environment	IP44 rated Suitable for indoor use only. Suitable for alfresco, porch and bathroom use.
Rating   Image Modified	Suitable for residential or commercial use in Australia and New Zealand. Used where air transfer is not permitted or not desired between living space and roof space (there will be no air transfer between spaces even if there is no insulation covering the luminaire). These luminaires have been tested to 90oC and will automatically reduce in brightness to prevent over temperature.
Requirements	An iZone bridge (COCB) is required to control an iZone smart light
Size & Weight	Height: 69 mm (51 mm without antenna cover) Diameter 109.6 mm Hole cut size: 90 mm Weight 154 g (excludes transformer and lead)

1️⃣ Ensure power supply is isolated before starting any work

2️⃣ Ensure downlight is located with minimum clearances from combustible building material as shown below

3️⃣ Connect mains power cable

4️⃣ Rotate spring clips up and gently insert downlight into hole

5️⃣ Pair down light

1️⃣ Ensure your iZone bridge is paired to your modem

2️⃣ Download the iZone Home App onto your smart device

3️⃣ Ensure your light is installed and wired

1️⃣ iZone RGB Light: Typical iZone RGB light bulb or down light

2️⃣ Flashing Red: When powered the light will flash red. This indicates the light is in its factory default setting and waiting to be paired to the system

3️⃣ Press the pair icon: On the touch screen or App > press the pair icon to pair the red flashing light to the system

4️⃣ Typical pair icon: In the "Devices" section of the App or touch screen there will be a pair button as shown. When the iZone RGB light is flashing red press this button to pair the light to the system

5️⃣ iZone RGB light will change to green: The iZone RGB light will change from flashing red to green when it has been paired to system

6️⃣ New light will be named L#: The newly paired light will be prefixed with the letter L, followed by a the next available number. In this example it is L5. If multiple lights are paired at the same time they will be shown as a single light

7️⃣ Indicates the light is turned on: The switch position indicates this light is switched on

8️⃣ Indicates current brightness: The brightness is represented a percentage. In this example it is 100%

9️⃣ Indicates current colour: The small box indicates the colour this light is currently set to

1️⃣ 0️⃣ Special Effect active: This column shows what special effect is set for this light

2️⃣

1️⃣ Power off the smart hub that the light has been paired to

1. On your interface:

   1. Nexus or Nano controller: Go to Device Config > and find Change Bridge.

   2. On Nova: Tap Menu > Settings > System ID Number > and find Change Bridge.

   3. On the iZone Home app: Go to Menu > Account > System ID > and find Change Bridge.

2. Leave the light on for at least 15 minutes.

1. Power off the light and power it on again

1. .

2. Tap on Change Bridge you have located earlier.

3. The light should now start

1. flashing red, indicating

1. it has successfully

1. reset

1. and unpaired.