| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
PAGE CONTENTS |
| Table of Contents | ||||
|---|---|---|---|---|
|
| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
PHOTO & DESCRIPTION |
The CRFS2 is a compact wireless sensor used for the control of zone temperatures and air conditioning units on iZone systems
1️⃣ Antenna: The sensor antenna transmits the status of the sensor to the C225 module using iZone proprietary 433mHz wireless protocol
2️⃣ Pair Button: Press the pair button to pair the sensor to the system. See details in configuration on how to pair a sensor
3️⃣ Sensor: The sensor measures the temperature of the air inside the sensor
4️⃣ Battery: The CR2032 battery is clipped into the battery holder. To remove the battery requires a small screw driver or similar tool to ensure they are child proof
The battery should last between 1-2 years before requiring replacement
5️⃣ Indicator: This indicates the direction you want to install the compact sensor onto the wall
6️⃣ Pair Button: Press the pair button to pair the sensor to the system. See details in configuration on how to pair a sensor
7️⃣ Battery Plate: The battery is held in place by the battery backing plate
8️⃣ Battery Tab: The clear plastic battery tab will be here, simply pull on the plastic to remove it
| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
SPECIFICATIONS |
Model Number | CRFS2 |
Power Supply (included) | CR2032 battery |
Battery Life | Approx. 1-2 years |
Casing Material | Polycarbonate and ABS plastic Facia colours available - White |
Operating Temperature | 80 to -14oC |
Communications Protocols | RF 433 MHz - Wireless |
Communication Range | Free field approximately 50 meters. (In a building the range will vary depending on the wall, roof and furniture materials which the radio signals needs to pass through) |
O/A Dimensions | Height 15 mm Width 35 mm Length 35 mm |
Weight (Excludes power supply) | 22g |
| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
QUICK GUIDE - HOW TO PAIR AWIRELESS SENSOR TO CPU? |
Remove the wireless sensor cover gently, using a flathead screwdriver
Remove the battery tab
Press and hold the PAIR button on the sensor and press PAIR icon on screen
Blue LED will flash rapidly and screen prompts updating information
Using a small flathead screwdriver, set the dip switch number on sensor to match it with the zone number that sensor will be installed
Click on Settings > Configuration > Configure Aircon > insert system password ‘wamfud’> Click on zones tab and change zone type to WIRELESS
Back in main menu, click on the zones summary and press the sensor button
When LED turns blue on sensor, zone status will change to climate control
When LED turns red on sensor, zone status will change to close
Make sure you see all three temperature setpoints, actual temperature and induct temperature on the screen
COMPACT SENSOR |
1️⃣ Use mini level and mark wall with pencil, best situated at 1600mm from ground (But not directly under ceiling outlet)
2️⃣ Pull compact sensor apart into 2 parts – Sensor and Wall attachment
3️⃣ Peel off sticky back from wall attachment and stick to wall, take note of which side is indicating ‘UP’
4️⃣ Mark wall attachment with zone number/name
5️⃣ Remove battery tab
6️⃣ Go to screen or open App
7️⃣ Hold down pair button on sensor, make sure blue light is visible when pressing pair button indicating battery is active
8️⃣ Click pair button on screen or App
9️⃣ Choose which zone you want to pair to (or RF sensor)
1️⃣0️⃣ Continue holding pair button and now select Pair
1️⃣1️⃣ Notification will either succeed or fail, if failed repeat above steps
1️⃣2️⃣ Once successful, change zone to climate
1️⃣3️⃣ Mark sensor with zone number/name on battery tab, not the front!
1️⃣4️⃣ Head back to wall attachments and match up sensor and wall attachment with marked zone name/numbers
1️⃣5️⃣ Insert sensor, take note of which side is indicating ‘UP’
| Panel | ||||||||
|---|---|---|---|---|---|---|---|---|
| ||||||||
VIDEO GUIDE - HOW TO PAIR A |
COMPACT SENSOR |
wmv