Page Comparison

• 1080p video with 180° Super Wide Angle

• Advanced Motion Detection

• Real 2-way Audio

• Voice Message

• Colour Night Vision

• Local Storage

• Built-in 100dB Siren

• Facial Recognition

• Hard wired. Requires an iZone 24V Doorbell transformer (CVDT)

1️⃣ Night light

2️⃣ PIR Sensor

3️⃣ Camera

4️⃣ Microphone

5️⃣ Doorbell Button

6️⃣ Speaker

7️⃣ Terminal Screws

8️⃣ Reset Button

• It is highly recommended that you switch the power off on your circuit breaker before installing your doorbell

1️⃣ Remove the base plate: Slide down to remove the base plate from the doorbell

2️⃣ Install a micro SD card: If you want to install a micro SD card (Purchase separately), push back the to remove the PIR module, insert a micro SD card into the SD card slot, and then replace the PIR module. Slide down to remove the base plate from the doorbell. iZone supports a micro SD card up to 128GB. Please ensure the SD card is formatted to FAT32

The iZone doorbell requires a micro SD card for local storage of video recordings and voice messages. If you intend to use video storage it is recommended that you install a micro SD card prior to installing the iZone doorbell as installing the micro SD card requires uninstalling the iZone doorbell from the base plate

3️⃣ Install the 24V power supply and associated cable: Install the 24V power supply (CVDT) and run the cables down the wall cavity or as required for your installation. It is recommend that an electrician is used to install the power supply and cables

4️⃣ Stick installation sticker on the wall: Stick the installation sticker on the wall so that the wires go through the centre hole on the sticker

Or if your wall has an uneven surface and the sticker won't hold, you can also use a pen to mark the four spots on the wall

5️⃣ Drill holes: Use the provided drill bit or one suitable for the wall material to drill 4 X holes at the marked spots on the sticker. Remove the sticker when you have finished

6️⃣ Insert the plastic anchors: Put the plastic anchors into the 4 holes. If necessary, use a hammer to gently tap them in until they are flush with the wall

7️⃣ Install the base plate: Place the base plate over the holes, and use the screws provided to secure the base plate

8️⃣ Remove the screws: Use the screwdriver provided to remove the two screws from the back of the iZone Doorbell

9️⃣ Secure the wires to the terminals: It doesn't matter which wire attaches to which terminal as the doorbell is not polarity sensitive

1️⃣ 0️⃣ Prepare the tamper proof screw: Drive the provided tamperproof screw slightly into the bottom screw hole on the iZone doorbell. Please make sure the tip of the screw stays beneath the end of the screw hole

1️⃣ 1️⃣ Mount the iZone Doorbell on the base plate: Slide the doorbell down on the base plate until it's in place. Tighten the tamper proof screws

1️⃣ Make sure you have a iZone Worldwide account set up and linked to at least one iZone system.

2️⃣ If you want to control security functions from your iZone Nexus screen, make sure your bridge (COCB) and Nexus firmware meets the required software version

3️⃣ You iZone Bridge must be ONLINE

4️⃣ Will need the home network name and password to link the Doorbell to their iZone system.

1️⃣ Login to your iZone Worldwide account

2️⃣ By default, the Security menu is hidden in the iZone Home App

1️⃣ Security Tab: This tab will be hidden as a factory default

2️⃣ Access the Configuration menu: Go to Settings> Configuration (for any service)> Navigate to the “Security” tab

3️⃣ Move slider to "Un-hide" Security System: Turn off “Hide System in App” (Factory default is hidden). The Security system Tab will now be displayed

4️⃣ Security Section will be displayed: The Security section will be displayed on the home screen

1️⃣ Open the iZone Home App, and scroll down to the “Security” section, press the “Pair” button.

2️⃣ Following the instruction in the App - Step by Step.

3️⃣ When complete the paired doorbell will appear in “Cameras” list.