| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
PAGE CONTENTS |
| Table of Contents |
|---|
| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
PHOTO & DESCRIPTION |
1️⃣ AC transformer: The transformer provides 24V power to the C150 module and is used to power all the zone dampers and connected modules
24V AC lead: The 24V lead consists of active and neutral conductors.
EMC ferrite
Molex Micro-Fit Connector: MICROFIT 3.0 RECPT 1 ROW V-0 TPA 02 CKT two wire connector is active and neutral. The connector on the transformer is female and it connects into the male connector on the C150 module
240V AC lead: The 240V lead consists of active, neutral and earth conductors
AU Plug: Standard 3 Pin AU plugZone RGB LED lights need to be paired to the iZone Bridge (COCB) to enable them to be controlled
Pairing can be done via the touch screen or the iZone Home App
Once paired a light can be grouped to other lights, switches, modules or they can be added to a Recipe for simple control logic
Pairing modules and switches is usually done manually by pressing the pairing button and at the same time pressing the pair button on the screen or app
1️⃣ Facia: 3 facia colours are available (White, Silver, Black)
2️⃣ Spring clips: Strong spring clips with rubber boots
3️⃣ Diffuser: Plastic diffuser
4️⃣ Aluminium body: The aluminium body is extremely durable and the cooling fins ensure the down light does not over heat and damage the electronics
| Panel | ||||||||
|---|---|---|---|---|---|---|---|---|
| The power supply to the transformer should be via an earthed AU GPO and should not be fed off the same circuit as the AC unit power supply.
| |||||||
Each light has an on board temperature sensor which is displayed on the screen and is used as a safety to prevent the light from overheating and failing prematurely |
5️⃣ Antenna: A small antenna protrudes from the casing for wireless communications (Not shown in this image)
| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
SPECIFICATIONS |
Model numbers |
CT24ACM
Input
240V ~ 50Hz
Output
AC 24V, 1000mA
Casing material
Fire retardant ABS plastic
Operating temperature
Up to 65oC
240V lead length
1400 mm (Approx)
24V lead length
1400 mm (Approx)
O/A Dimensions
Height 65 mm
Width 75 mm
Length 99 mm
Weight
CL5DB, CL5DS, and CL5DW | |
Certification | AS/NZS 60598.2.2; AS/NZS 61347.2.13; C Tick N29007; IP44; IC-4; SAA |
Power supply | Input: 220 - 240VAC 66mA ~ 50Hz |
Connection | 2 Pin Australian GPO plug |
Transformer | Custom transformer included. Output: 25V DC ~ 280mA The driver supplied is SELV EQUIVALENT |
Power lead | 1.2 meters |
Power consumption | Maximum 9.0 Watts on full brightness (Cool white) Minimum 0.22 Watts in standby mode |
Brightness | Maximum 523.7 Lumens |
Efficiency | 36.5 Lumens / Watt (Cool White) |
Beam Angle | 88.9 |
Control frequency | 433 MHz |
Operating Temperature | -20oC to +50oC |
Environment | IP44 rated Suitable for indoor use only. Suitable for alfresco, porch and bathroom use. |
Rating
.png) | Suitable for residential or commercial use in Australia and New Zealand. Used where air transfer is not permitted or not desired between living space and roof space (there will be no air transfer between spaces even if there is no insulation covering the luminaire). These luminaires have been tested to 90oC and will automatically reduce in brightness to prevent over temperature. |
Requirements | An iZone bridge (COCB) is required to control an iZone smart light |
Size & Weight | Height: 69 mm (51 mm without antenna cover) Diameter 109.6 mm Hole cut size: 90 mm Weight 154 g (excludes transformer and lead) |