| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
PAGE CONTENTS |
| Table of Contents | ||||
|---|---|---|---|---|
|
| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
PHOTO & DESCRIPTION |
Zone RGB LED lights need to be paired to the iZone Bridge (COCB) to enable them to be controlled
Pairing can be done via the touch screen or the iZone Home App
Once paired a light can be grouped to other lights, switches, modules or they can be added to a Recipe for simple control logic
Pairing modules and switches is usually done manually by pressing the pairing button and at the same time pressing the pair button on the screen or app
1️⃣ Facia: 3 facia colours are available (White, Silver, Black)
2️⃣ Spring clips: Strong spring clips with rubber boots
3️⃣ Diffuser: Plastic diffuser
4️⃣ Aluminium body: The aluminium body is extremely durable and the cooling fins ensure the down light does not over heat and damage the electronics
| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
Each light has an on board temperature sensor which is displayed on the screen and is used as a safety to prevent the light from overheating and failing prematurely |
5️⃣ Antenna: A small antenna protrudes from the casing for wireless communications (Not shown in this image)
| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
SPECIFICATIONS |
Model numbers | CL5DB, CL5DS, and CL5DW |
Certification | AS/NZS 60598.2.2; AS/NZS 61347.2.13; C Tick N29007; IP44; IC-4; SAA |
Power supply | Input: 220 - 240VAC 66mA ~ 50Hz |
Connection | 2 Pin Australian GPO plug |
Transformer | Custom transformer included. Output: 25V DC ~ 280mA The driver supplied is SELV EQUIVALENT |
Power lead | 1.2 meters |
Power consumption | Maximum 9.0 Watts on full brightness (Cool white) Minimum 0.22 Watts in standby mode |
Brightness | Maximum 523.7 Lumens |
Efficiency | 36.5 Lumens / Watt (Cool White) |
Beam Angle | 88.9 |
Control frequency | 433 MHz |
Operating Temperature | -20oC to +50oC |
Environment | IP44 rated Suitable for indoor use only. Suitable for alfresco, porch and bathroom use. |
Rating
.png) | Suitable for residential or commercial use in Australia and New Zealand. Used where air transfer is not permitted or not desired between living space and roof space (there will be no air transfer between spaces even if there is no insulation covering the luminaire). These luminaires have been tested to 90oC and will automatically reduce in brightness to prevent over temperature. |
Requirements | An iZone bridge (COCB) is required to control an iZone smart light |
Size & Weight | Height: 69 mm (51 mm without antenna cover) Diameter 109.6 mm Hole cut size: 90 mm Weight 154 g (excludes transformer and lead) |
| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
DOWNLIGHT INSTALLATION |
| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
This product must be installed by a qualified licenced electrician in accordance with AS/NZ 3000:2007 Electrical installations |
| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
Please note: Accidental contact with live parts does not rely on the luminaire enclosure |
| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
Warning this product is not suitable for mounting on tubular material |
1️⃣ Ensure power supply is isolated before starting any work
2️⃣ Ensure downlight is located with minimum clearances from combustible building material as shown below
3️⃣ Connect mains power cable
4️⃣ Rotate spring clips up and gently insert downlight into hole
5️⃣ Pair down light
| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
PAIRING A DOWNLIGHT GUIDE |
| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
BEFORE YOU GET STARTED… |
1️⃣ Ensure your iZone bridge is paired to your modem
2️⃣ Download the iZone Home App onto your smart device
3️⃣ Ensure your light is installed and wired
| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
For the purposes of this manual reference to an iZone RGB light refers to either an iZone RGB light bulb or and iZone RGB Down light |
| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
Tip: If you want to group multiple lights together you can pair them simultaneously. If you want each light to be on its own pair them one at a time. You can also group individually paired lights later using the group functions |
| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
DOWNLIGHT PAIRING |
1️⃣ iZone RGB Light: Typical iZone RGB light bulb or down light
2️⃣ Flashing Red: When powered the light will flash red. This indicates the light is in its factory default setting and waiting to be paired to the system
| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
If it is not flashing red you will need to reset the light to its factory default setting |
3️⃣ Press the pair icon: On the touch screen or App > press the pair icon to pair the red flashing light to the system
4️⃣ Typical pair icon: In the "Devices" section of the App or touch screen there will be a pair button as shown. When the iZone RGB light is flashing red press this button to pair the light to the system
5️⃣ iZone RGB light will change to green: The iZone RGB light will change from flashing red to green when it has been paired to system
6️⃣ New light will be named L#: The newly paired light will be prefixed with the letter L, followed by a the next available number. In this example it is L5. If multiple lights are paired at the same time they will be shown as a single light
7️⃣ Indicates the light is turned on: The switch position indicates this light is switched on
8️⃣ Indicates current brightness: The brightness is represented a percentage. In this example it is 100%
9️⃣ Indicates current colour: The small box indicates the colour this light is currently set to
1️⃣ 0️⃣ Special Effect active: This column shows what special effect is set for this light
| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
FACTORY DEFAULT RESET |
1️⃣ Power off the smart hub that the light has been paired to
2️⃣ Leave the light on for at least 15 minutes
3️⃣ Power off the light and power on again, the light should now start to flash red, indicating you have successfully factory reset the light