Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Panel
panelIconIdatlassian-info
panelIcon:info:
bgColor#B3D4FF

PAGE CONTENTS

Table of Contents

Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#C0B6F2

PHOTO AND DESCRIPTION

The relay module is hard wired to the mains power and uses wireless RF for the control communication

To comply with Australian / NZ wiring rules a relay module should always be used when controlling circuits that require the control device to be installed in the roof space

Smart plugs should not be installed in the roof void

This module is only suitable for locating indoors, however, it can control devices which have a suitable rating that are located outdoors or in wet areas

1️⃣ Wireless antenna:

The wireless antenna should be screwed in tight and after installation it should point up

2️⃣ Manual On/Off button:

To test the LED dimmer module you can press this manual on/off button to turn the lighting circuit on and off

3️⃣ Pair button:

To pair the LED dimmer module to the system ensure there is power to the LED dimmer module> Press the pair button on the module > . At the same time press the pair button on the App or iZone touch screen >The blue LED inside the module (close to the pair button) will flash rapidly to indicate the module is pairing to the system

4️⃣ Remove cover to expose terminals:

Remove the terminal cover to expose the wiring terminal. Wire in accordance with the wiring notation on printed on the top cover. There are also wiring restraint cable ties that should be used to restrain the wiring in place. This should only be done by and electrician

5️⃣ Knock outs for wiring / conduits:

There are two knock outs for wiring or conduits to located on the end of the module. Drill or knock out accordingly

6️⃣ Mounting point:

There are two mounting points on the module to allow the module to be mounted to roof timbers

Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#C0B6F2

SPECIFICATION

Model numbers

CACR

Certification

AS/NZS 61058 ;  C Tick  N29007;  

Power supply

Input: 220 - 240VAC 50Hz

Power consumption

Maximum  2.45 Watts switched on (no load connected)

Minimum 1.05 Watts switched off

Maximum connected load permitted

15 amps 1 phase

Connection

Hard wired

Control frequency

433 MHz

Operating Temperature

-20oC to +50oC

Environment

Suitable for indoor use only

Requirements

An iZone bridge (COCB) is required to control an iZone relay module

Size & Weight

Height: 150 mm (Excludes mounting lugs and antenna)

Width 85 mm

Depth 36 mm (Excludes Antenna)

Weight 235g

(Designed to fit through a standard 95mm diameter down light hole)

 

Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#C0B6F2

INSTALLATION

1️⃣ Switch the power off at the switchboard

2️⃣ Remove the Relay module from the packaging

3️⃣ Cut the circuit to the device being controller and terminate the wiring as indicated on the casing

4️⃣ Test the relay and switching using the manual On/Off button on the module

Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#C0B6F2

PAIRING

1️⃣ Pair the iZone Dimmer module to the iZone Bridge by pressing the pair button on the Dimmer module and on the screen simultaneously

Image RemovedImage Added

2️⃣ The blue LED adjacent to the pair button on the module will flash blue several times to indicate it is pairing

Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#C0B6F2

CONFIGURATION

1️⃣ Name your Dimmer module on the screen or app

2️⃣ Group your Dimmer module to other devices or switches