PAGE CONTENTS
The following bridge was superseded by the COCB. The information provided is for existing systems that are still in the field and may require maintenance or repairs
PHOTO & DESCRIPTION
The CB is a wireless or wired bridge that connects the iZone air conditioning system to the home Wi-Fi to enable the the control of iZone system via a smart phone or tablet
1️⃣ iZone Net Connection: If a wired connection between the C225 module and this bridge is required a special cable (CGB2C35) is used to connect the C225 module and the bridge via this iZone Net Port
2️⃣ Pair Button: The pair button is used to pair the CB to the C225 system
3️⃣ Ethernet Connection: Connect the CB to the customers modem via this Ethernet port
4️⃣ Ethernet Activity LED: The LED is on, when connected to a Wi-Fi network, or off when not connected to a Wi-Fi network
5️⃣ Activity LED: Indicates activity on both interfaces, Ethernet and iZone Net (RF or CAN)
6️⃣ iZone C225 Activity: The LED is on, when connected to a C225 module, or off when not connected to a C225 module
SPECIFICATIONS
Model Number | CB |
Power Supply | Built in or separate AC/DC Adaptor Input: 100-240V ~0.3A 50-60Hz Output: 5V ~1A |
Casing material | Fire retardant ABS plastic |
Operating Temperature | Up to 45oC |
Communications protocols | RF 433 MHz - Wireless CAN Bus - Wired |
O/A Dimensions (With power supply assembled) | Height 60 mm (Excludes Antenna) Width 61 mm Length 110 mm |
Weight (With power supply assembled) | 213g |
WIRELESS SETUP DIAGRAM
1️⃣ iZone Bridge CB: For the most effective iZone wireless coverage locate the bridge as close as possible to the middle of the building off the floor
Do not mount the bridge inside a metal cabinet as this will block the radio transmission to and from the bridge. If this is unavoidable install an antenna extender and locate the antenna outside of the cabinet
2️⃣ CFC1S: 1 meter long Ethernet cable supplied with the bridge. Longer Ethernet cables can be used provided they meet the required specification
3️⃣ Customers modem / router: The customers modem must be compatible with iZone. See link to incompatible modems here
4️⃣ Ethernet port: Connect the CFC1S cable provided into the Ethernet port on the iZone bridge
5️⃣ LAN port: Connect the CFC1S cable provided with the iZone bridge into a LAN port on the modem / router
6️⃣ WAN Port:
Do not connect to a router's WAN port
7️⃣ Bridge power adaptor: Connect the iZone power adaptor supplied with the bridge into the port labelled "Power". Plug the power supply into a suitable 240 AC GPO
8️⃣ Pair button: Press and hold down the pair button whilst you press the pair button on the iZone controller to pair the two wireless parts to the system.
9️⃣ Pair LED: The pair LED will flash rapidly when the bridge is pairing to the iZone system
WIRED SETUP DIAGRAM
QUICK GUIDE - HOW TO PAIR THE IZONE BRIDGE TO THE CPU?
Plug in your iZone Wi-Fi bridge to a power point
Press and hold down the pair button on the bridge
While holding the pair button, press the pair icon on the screen
Once the pair LED flashes rapidly, you can release the pair button on the bridge
Wait for the LEDs on the bridge to spin around, the LED with no label or icon stays on
This means the bridge is paired with CPU successfully
After a few seconds all the home automation options will appear on the home screen
Now plug in your bridge to the Wi-Fi modem using the LAN cable provided
Connect the LAN cable to the ethernet port on the bridge and LAN port on the modem
When the bridge is connected to the modem, the LED with the globe icon on the bridge shows blue and the ethernet port orange and green lights stay on
DOUBLE CHECK THE CONNECTED BRIDGE INFORMATION
Insert system password ‘wamfud', press enter, Then click on Wi-Fi bridge configuration
You will see system ID number, IP and MAC address
Now you can download the iZone Home App on your device and start using your new smart home system via your device