Panel | ||||||
---|---|---|---|---|---|---|
| ||||||
PAGE CONTENTS |
Table of Contents | ||||
---|---|---|---|---|
|
Panel | ||||||
---|---|---|---|---|---|---|
| ||||||
The following bridge was superseded by the COCB. The information provided is for existing systems that are still in the field and may require maintenance or repairs |
Panel | ||||||
---|---|---|---|---|---|---|
| ||||||
PHOTO & DESCRIPTION |
The CL5B is a wireless or wired bridge that connects the iZone air conditioning and lighting systems to the home Wi-Fi to enable the control of iZone systems via a smart phone, tablet or voice activation via a 3rd party device
1️⃣ iZone Net Port: If a wired connection between the C225 module and this bridge is required a special cable (CGB2C35) is used to connect the C225 module and the bridge via this iZone Net Port
2️⃣ Pair button: The pair button is used to pair the CL5B to the C225 system
3️⃣ Ethernet port: Connect the CL5B to the customers modem via this Ethernet port
4️⃣ 433 MHz wireless antenna: For wireless communication with C225 and wireless iZone devices
5️⃣ Ethernet activity LED: The LED is on, when connected to a Wi-Fi network, or off when not connected to a Wi-Fi network
6️⃣ Activity LED: Indicates activity on both interfaces, Ethernet and iZone Net (RF or CAN)
7️⃣ C225 Activity: The LED is on, when connected to a C225 module, or off when not connected to a C225 module
Panel | ||||||
---|---|---|---|---|---|---|
| ||||||
SPECIFICATIONS |
Model Number | CL5B & CL5BK |
Power Supply | Built in or separate AC/DC Adaptor Input: 100-240V ~0.3A 50-60Hz Output: 5V ~1A |
Casing material | Fire retardant ABS plastic |
Operating Temperature | Up to 45oC |
Communications protocols | RF 433 MHz - Wireless CAN Bus - Wired |
Cable included (CL5BK Only) | CFC1S (CAT5E Shielded Cable) |
O/A Dimensions (With power supply assembled) | Height 60 mm (Excludes Antenna) Width 61 mm Length 110 mm |
Weight (With power supply assembled) | 213g |
Panel | ||||||
---|---|---|---|---|---|---|
| ||||||
WIRELESS SETUP DIAGRAM |
1️⃣ iZone Bridge CL5B: For the most effective iZone wireless coverage locate the bridge as close as possible to the middle of the building off the floor
Panel | ||||||
---|---|---|---|---|---|---|
| ||||||
Do not mount the bridge inside a metal cabinet as this will block the radio transmission to and from the bridge. If this is unavoidable install an antenna extender and locate the antenna outside of the cabinet |
2️⃣ CFC1S: 1 meter long Ethernet cable supplied with the bridge. Longer Ethernet cables can be used provided they meet the required specification
3️⃣ Customers modem / router: The customers modem must be compatible with iZone. See link to incompatible modems here
4️⃣ Ethernet port: Connect the CFC1S cable provided into the Ethernet port on the iZone bridge
5️⃣ LAN port: Connect the CFC1S cable provided with the iZone bridge into a LAN port on the modem / router
6️⃣ WAN Port:
Panel | ||||||
---|---|---|---|---|---|---|
| ||||||
Do not connect to a router's WAN port |
7️⃣ Bridge power adaptor: Connect the iZone power adaptor supplied with the bridge into the port labelled "Power". Plug the power supply into a suitable 240 AC GPO
8️⃣ Pair button: Press and hold down the pair button whilst you press the pair button on the iZone controller to pair the two wireless parts to the system.
9️⃣ Pair LED: The pair LED will flash rapidly when the bridge is pairing to the iZone system
Panel | ||||||
---|---|---|---|---|---|---|
| ||||||
WIRED SETUP DIAGRAM |
Panel | ||||||
---|---|---|---|---|---|---|
| ||||||
QUICK GUIDE - HOW TO PAIR THE IZONE BRIDGE TO THE CPU? |
Plug in your iZone Wi-Fi bridge to a power point
Press and hold down the pair button on the bridge
While holding the pair button, press the pair icon on the screen
If you don’t have a screen, you can pair the bridge via the iZone CPU, press and hold the pair button on the bridge and then click once on the iZone CPU’s pair button, you will then see the LED lights start to spin, indicating the bridge has paired to the CPU, continue on from #8 below
Once the pair LED flashes rapidly, you can release the pair button on the bridge
Wait for the LEDs on the bridge to spin around, the LED with no label or icon stays on
This means the bridge is paired with CPU successfully
After a few seconds all the home automation options will appear on the home screen
Now plug in your bridge to the Wi-Fi modem using the LAN cable provided
Connect the LAN cable to the ethernet port on the bridge and LAN port on the modem
When the bridge is connected to the modem, the LED with the globe icon on the bridge shows blue and the ethernet port orange and green lights stay on
Panel | ||||||
---|---|---|---|---|---|---|
| ||||||
DOUBLE CHECK THE CONNECTED BRIDGE INFORMATION |
Insert system password ‘wamfud', press enter, Then click on Wi-Fi bridge configuration
You will see system ID number, IP and MAC address
Now you can download the iZone Home App on your device and start using your new smart home system via your device
Panel | ||||||||
---|---|---|---|---|---|---|---|---|
| ||||||||
VIDEO GUIDE - HOW TO PAIR THE IZONE BRIDGE TO THE CPU? |