Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 7 Next »

PAGE CONTENTS

The following bridge was superseded by the COCB. The information provided is for existing systems that are still in the field and may require maintenance or repairs

PHOTO & DESCRIPTION

The CL5B is a wireless or wired bridge that connects the iZone air conditioning and lighting systems to the home Wi-Fi to enable the control of iZone systems via a smart phone, tablet or voice activation via a 3rd party device

1️⃣ iZone Net Port: If a wired connection between the C225 module and this bridge is required a special cable (CGB2C35) is used to connect the C225 module and the bridge via this iZone Net Port

2️⃣ Pair button: The pair button is used to pair the CL5B to the C225 system

3️⃣ Ethernet port: Connect the CL5B to the customers modem via this Ethernet port

4️⃣ 433 MHz wireless antenna: For wireless communication with C225 and wireless iZone devices

5️⃣ Ethernet activity LED: The LED is on, when connected to a Wi-Fi network, or off when not connected to a Wi-Fi network

6️⃣ Activity LED: Indicates activity on both interfaces, Ethernet and iZone Net (RF or CAN)

7️⃣ C225 Activity: The LED is on, when connected to a C225 module, or off when not connected to a C225 module

SPECIFICATIONS

Model Number

CL5B & CL5BK

Power Supply

Built in or separate

AC/DC Adaptor

Input: 100-240V ~0.3A 50-60Hz

Output: 5V ~1A

Casing material

Fire retardant ABS plastic

Operating Temperature

Up to 45oC

Communications protocols

RF 433 MHz - Wireless

CAN Bus - Wired

Cable included (CL5BK Only)

CFC1S  (CAT5E Shielded Cable)  

O/A Dimensions (With power supply assembled)

Height 60 mm (Excludes Antenna)

Width 61 mm

Length 110 mm

Weight (With power supply assembled)

 213g

WIRELESS SETUP DIAGRAM

scrrensh.png

1️⃣ iZone Bridge CL5B: For the most effective iZone wireless coverage locate the bridge as close as possible to the middle of the building off the floor

Do not mount the bridge inside a metal cabinet as this will block the radio transmission to and from the bridge. If this is unavoidable install an antenna extender and locate the antenna outside of the cabinet

2️⃣ CFC1S: 1 meter long Ethernet cable supplied with the bridge. Longer Ethernet cables can be used provided they meet the required specification

3️⃣ Customers modem / router: The customers modem must be compatible with iZone. See link to incompatible modems here

4️⃣ Ethernet port: Connect the CFC1S cable provided into the Ethernet port on the iZone bridge

5️⃣ LAN port: Connect the CFC1S cable provided with the iZone bridge into a LAN port on the modem / router

6️⃣ WAN Port:

Do not connect to a router's WAN port

7️⃣ Bridge power adaptor: Connect the iZone power adaptor supplied with the bridge into the port labelled "Power". Plug the power supply into a suitable 240 AC GPO

8️⃣ Pair button: Press and hold down the pair button whilst you press the pair button on the iZone controller to pair the two wireless parts to the system.

9️⃣ Pair LED: The pair LED will flash rapidly when the bridge is pairing to the iZone system

WIRED SETUP DIAGRAM

QUICK GUIDE - HOW TO PAIR THE IZONE BRIDGE TO THE CPU?

  1. Plug in your iZone Wi-Fi bridge to a power point

  2. Press and hold down the pair button on the bridge

  3. While holding the pair button, press the pair icon on the screen

    1. If you don’t have a screen, you can pair the bridge via the iZone CPU, press and hold the pair button on the bridge and then click once on the iZone CPU’s pair button, you will then see the LED lights start to spin, indicating the bridge has paired to the CPU, continue on from #8 below

  4. Once the pair LED flashes rapidly, you can release the pair button on the bridge

  5. Wait for the LEDs on the bridge to spin around, the LED with no label or icon stays on

  6. This means the bridge is paired with CPU successfully

  7. After a few seconds all the home automation options will appear on the home screen

  8. Now plug in your bridge to the Wi-Fi modem using the LAN cable provided

  9. Connect the LAN cable to the ethernet port on the bridge and LAN port on the modem

  10. When the bridge is connected to the modem, the LED with the globe icon on the bridge shows blue and the ethernet port orange and green lights stay on

DOUBLE CHECK THE CONNECTED BRIDGE INFORMATION

  1. Insert system password ‘wamfud', press enter, Then click on Wi-Fi bridge configuration

  2. You will see system ID number, IP and MAC address

  3. Now you can download the iZone Home App on your device and start using your new smart home system via your device

VIDEO GUIDE - HOW TO PAIR THE IZONE BRIDGE TO THE CPU?

VideoEditor_20240417_030910 (1).mp4

  • No labels