| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
PAGE CONTENTS |
| Table of Contents | ||||
|---|---|---|---|---|
|
| Panel | ||||||
|---|---|---|---|---|---|---|
|
...
PHOTO & DESCRIPTION |
The iZone basic LED down lights is a low cost "dumb" LED
If used in conjunction with and iZone LED Dimmer module or iZone LED Dimmer + Switch module it can be controlled via your iZone system
The colour temperate can be altered by a three position dip switch on the top of transformer casing
...
1️⃣ Plastic Facia: Only available in white
2️⃣ Spring clips: Strong spring clips with rubber boots
3️⃣ Diffuser: Plastic diffuser
4️⃣ Composite body: The body is a composite of metal and plastic
5️⃣ Transformer: The transformer is built into the LED body
| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
SPECIFICATIONS |
Model numbers | CLIGHT |
Certification | AS/NZS 60598.2.2; C Tick, SAA, CE, IP44; IC-4 |
Power supply | Input: 220 - 240VAC ~ 50/60Hz |
Connection | 2 Pin Australian GPO plug |
Transformer | Built in |
Power lead | 0.6 meters |
Power consumption | Maximum 10.0 Watts on full brightness (4000K)
|
Brightness | Maximum 794 Lumens |
Colour adjustable | Cool (6000K) Neutral (4000K) Warm (3000K) (Manual control via dip switch on the top of the down light) |
Efficiency | 80 Lumens / Watt (Cool White) |
Beam Angle | 120 |
Dimmable / controllable | Yes - fully compatible with iZone Relay, Dimmer and Dimmer + switch module (CACR, CACD & CADSW) |
Operating Temperature | -20oC to +50oC |
Environment | IP44 rated Suitable for indoor use only. Suitable for alfresco, porch and bathroom use. |
Rating
.png) | Suitable for residential or commercial use in Australia and New Zealand. Used where air transfer is not permitted or not desired between living space and roof space (there will be no air transfer between spaces even if there is no insulation covering the luminaire). These luminaires have been tested to 90oC and will automatically reduce in brightness to prevent over temperature. |
Size & Weight | Height: 58 mm Diameter 115 mm Hole cut size: 90 mm Weight 192 g |
| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
INSTALLATION |
| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
This product must be installed by a qualified licenced electrician in accordance with AS/NZ 3000:2007 Electrical installations |
| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
Please note: Accidental contact with live parts does not rely on the luminaire enclosure |
| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
Warning this product is not suitable for mounting on tubular material |
1️⃣ Ensure power supply is isolated before starting any work
2️⃣ Ensure downlight is located with minimum clearances from combustible building material as shown below
3️⃣ Connect mains power cable
4️⃣ Rotate spring clips up and gently insert downlight into hole
5️⃣ Pair down light
...
| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
PAIRING A DOWNLIGHT GUIDE |
| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
BEFORE YOU GET STARTED… |
1️⃣ Ensure your iZone bridge is paired to your modem
2️⃣ Download the iZone Home App onto your smart device
3️⃣ Ensure your light is installed and wired
| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
For the purposes of this manual reference to an iZone RGB light refers to either an iZone RGB light bulb or and iZone RGB Down light |
| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
Tip: If you want to group multiple lights together you can pair them simultaneously. If you want each light to be on its own pair them one at a time. You can also group individually paired lights later using the group functions |
| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
DOWNLIGHT PAIRING |
...
1️⃣ iZone RGB Light: Typical iZone RGB light bulb or down light
2️⃣ Flashing Red: When powered the light will flash red. This indicates the light is in its factory default setting and waiting to be paired to the system
| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
If it is not flashing red you will need to reset the light to its factory default setting |
3️⃣ Press the pair icon: On the touch screen or App > press the pair icon to pair the red flashing light to the system
4️⃣ Typical pair icon: In the "Devices" section of the App or touch screen there will be a pair button as shown. When the iZone RGB light is flashing red press this button to pair the light to the system
5️⃣ iZone RGB light will change to green: The iZone RGB light will change from flashing red to green when it has been paired to system
6️⃣ New light will be named L#: The newly paired light will be prefixed with the letter L, followed by a the next available number. In this example it is L5. If multiple lights are paired at the same time they will be shown as a single light
7️⃣ Indicates the light is turned on: The switch position indicates this light is switched on
8️⃣ Indicates current brightness: The brightness is represented a percentage. In this example it is 100%
9️⃣ Indicates current colour: The small box indicates the colour this light is currently set to
...