Page Comparison

110 is a basic low cost zone only control system which is suitable for switching zones Open and Closed

A summary of the features iZone 110 offers are listed below:

• Compatible with all leading air conditioning brands

• Up to 6 zones available

• Add up to 2 wall controllers

• Label zone names from a standard library of names

• Open zones are identified with a blue LED

• Up two zones can be configured as electronic constants

There is no facility to control the zones via Wi-Fi or automatically via temperature sensors. The iZone 110 does not interface with the air conditioning unit and the installation will require a separate controller for the air conditioning unit. Furthermore iZone 110 does not incorporate airflow control so balancing dampers should be included in the design

...

1️⃣ The C110MC can be installed on top of the indoor fan coil unit

2️⃣ Do not run the blue network cables alongside 240 Volt wiring

3️⃣ When installing network cables down wall cavities or chasing network cables into walls, tape up and protect the RJ45 connector to avoid damage to the connectors

4️⃣ Always install zones in consecutive ports starting at Zone 1. The back of the C110MC is marked with the zone port numbers

5️⃣ Do not directly hardwire the CT24ACE into the AC unit’s power supply. This may void the warranty as it will require an electrician in the event that repair of the iZone 110 system is required

6️⃣ Connect Zone Damper Actuators (CZDA) to the zone ports using the RJ12 cables as shown

7️⃣ Connect the Wall controller(s) (C110WC) to the C110WC ports using the RJ45 cables

8️⃣ Only connect the power supply to the CT24AC port after all components have been connected

9️⃣ Initialise the system

1️⃣ 0️⃣ Configure the system

All new or modified systems must be initialised prior to system configuration

To initialise the system press the button on the underside of any wall controller. This button is recessed so you will need to use a pen to press the button

The time to initialise the system will vary depending on the number of motors connected

The system will also initialise when power is restored after a power failure

...

iZone 150 Zone only is a basic low cost zone only control system which is suitable for switching zones Open and Closed

A summary of the features iZone 150 Zone only offers are listed below:

• Up to 6 zones available

• Zones air quantities can be balanced from the CEPC controller (no need for separate manual balancing dampers)

• Zone airflows can be adjusted by the end user from the CEPC controller

• Multiple CEPC controllers can be added

• Zone temperatures can be controlled from CEPC if iZone sensors are fitted to the system

• Label zone names from a standard library of names built into the controller

• Electronic constants can be set-up

...

1️⃣ The C150 can be installed on top of the indoor fan coil unit

2️⃣ Do not run the blue network cables alongside 240 Volt wiring

3️⃣ Always install zones in consecutive ports starting at Zone 1. The front of the C150 is marked with the zone port numbers

4️⃣ Do not directly hard wire the CT24ACM into the AC unit’s power supply. This may void the warranty as it will require an electrician in the event that repair of the iZone 150 system is required

5️⃣ Connect Zone Damper Actuators (CZDA) to the zone ports using the RJ12 cables as shown

6️⃣ Remove the tabs on the CEPC batteries to activate power to the controller

7️⃣ Only connect the power supply to the CT24ACM port after all components have been connected

8️⃣ Initialise the system

9️⃣ Configure the system

All new or modified systems must be initialised prior to system configuration

To initialise the system remove the power from the C150 module, wait 15 seconds and restore power to the C150 module

The time to initialise the system will vary depending on the number of motors connected

The system will also initialise when power is restored after a power failure

iZone 155 is a basic low cost zone only control system which is suitable for switching zones Open and Closed

A summary of the features of the iZone 155 zone only are listed below:

• Up to 6 zones available

• Zones air quantities can be balanced from the CEPC controller (no need for separate manual balancing dampers)

• Zone airflows can be adjusted by the end user from the CEPC controller

• Multiple CEPC controllers can be added

• Zone temperatures can be controlled from CEPC if iZone sensors are fitted to the system

• Label zone names from a standard library of names built into the controller. Customised names can be input via your smart device

• Electronic constants can be set up

• WiFi or 5G control of your zones and other smart iZone devices

...

1️⃣ The C150 can be installed on top of the indoor fan coil unit

2️⃣ Do not run the blue network cables alongside 240 Volt wiring

3️⃣ Always install zones in consecutive ports starting at Zone 1. The front of the C150 is marked with the zone port numbers

4️⃣ Do not directly hard wire the CT24ACM into the AC unit’s power supply. This may void the warranty as it will require an electrician in the event that repair of the iZone 150 system is required

5️⃣ Connect Zone Damper Actuators (CZDA) to the zone ports using the RJ12 cables as shown

6️⃣ Remove the tabs on the CEPC batteries to activate power to the controller

7️⃣ Only connect the power supply to the CT24ACM port after all components have been connected

8️⃣ Initialise the system

9️⃣ Configure the system

1️⃣ 0️⃣ Connect the bridge to the owners modem and connect the bridge power supply. Pair the bridge to the C155 using the pair button on the CEPC screen

All new or modified systems must be initialised prior to system configuration

To initialise the system remove the power from the C150 module, wait 15 seconds and restore power to the C150 module

The time to initialise the system will vary depending on the number of motors connected

The system will also initialise when power is restored after a power failure

iZone 155 is a low cost integrated AC control system which is suitable for controlling zones and complete AC unit control as well as full smart home control via a phone or tablet

A summary of the features iZone 155 offers are listed below:

• Up to 6 zones available

• Zones air quantities can be balanced from the CEPC controller (no need for separate manual balancing dampers)

• Zone airflows can be adjusted by the end user from the CEPC controller

• Multiple CEPC controllers can be added

• Zone temperatures can be controlled from CEPC if iZone sensors are fitted to the system

• Label zone names from a standard library of names built into the controller

• Electronic constants can be setup

• Numerous brands of AC unit can be controlled. Click on the link to which AC units are compatible and how to wire them

...

1️⃣ The C150 can be installed on top of the indoor fan coil unit

2️⃣ Do not run the blue network cables alongside 240 Volt wiring

3️⃣ Always install zones in consecutive ports starting at Zone 1. The front of the C150 is marked with the zone port numbers

4️⃣ Do not directly hard wire the CT24ACM into the AC unit’s power supply. This may void the warranty as it will require an electrician in the event that repair of the iZone 150 system is required

5️⃣ Connect Zone Damper Actuators (CZDA) to the zone ports using the RJ12 cables as shown

6️⃣ Connect the AC unit control cable to the C150 as per the instructions for your brand of AC unit found here

7️⃣ Remove the tabs on the CEPC batteries to activate power to the controller

8️⃣ Only connect the power supply to the CT24ACM port after all components have been connected

9️⃣ Initialise the system

1️⃣ 0️⃣ Configure the system

All new or modified systems must be initialised prior to system configuration

To initialise the system remove the power from the C150 module, wait 15 seconds and restore power to the C150 module

The time to initialise the system will vary depending on the number of motors connected

The system will also initialise when power is restored after a power failure

iZone 155 is a low cost integrated AC control system which is suitable for controlling zones and complete AC unit control as well as full smart home control via a phone or tablet

A summary of the features iZone 155 offers are listed below:

• Up to 6 zones available

• Zones air quantities can be balanced from the CEPC controller (no need for separate manual balancing dampers)

• Zone airflows can be adjusted by the end user from the CEPC controller

• Multiple CEPC controllers can be added

• Zone temperatures can be controlled from CEPC if iZone sensors are fitted to the system

• Label zone names from a standard library of names built into the controller

• Electronic constants can be setup

• Numerous brands of AC unit can be controlled. Click on the link to which AC units are compatible and how to wire them

...

1️⃣ The C150 can be installed on top of the indoor fan coil unit

2️⃣ Do not run the blue network cables alongside 240 Volt wiring

3️⃣ Always install zones in consecutive ports starting at Zone 1. The front of the C150 is marked with the zone port numbers

4️⃣ Do not directly hard wire the CT24ACM into the AC unit’s power supply. This may void the warranty as it will require an electrician in the event that repair of the iZone 150 system is required

5️⃣ Connect Zone Damper Actuators (CZDA) to the zone ports using the RJ12 cables as shown

6️⃣ Connect the AC unit control cable to the C150 as per the instructions for your brand of AC unit found here

7️⃣ Remove the tabs on the CEPC batteries to activate power to the controller

8️⃣ Only connect the power supply to the CT24ACM port after all components have been connected

9️⃣ Initialise the system

1️⃣ 0️⃣ Configure the system

1️⃣ 1️⃣ Connect the bridge to the owners modem and connect the bridge power supply. Pair the bridge to the C155 using the pair button on the CEPC screen

All new or modified systems must be initialised prior to system configuration

To initialise the system remove the power from the C150 module, wait 15 seconds and restore power to the C150 module

The time to initialise the system will vary depending on the number of motors connected

...