Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 11 Next »

PAGE CONTENTS

ONLINE INSTALLATION WIZARD

Scan the QR code below and you will be sent our online installation wizard for the C430 Series

Answer a few easy questions on:

1️⃣ What air conditioning unit are installing

2️⃣ Is the iZone home mobile app required

3️⃣ Type of constant/bypass zone

4️⃣ Number of Zones using temperature sensors

5️⃣ Number of Zones that are just open/close

➡️ Then click submit for a wiring diagram of the system and a step by step guide on how to install the iZone

The online installation wizard will cover all of the below installation steps:

1️⃣ Design Diagram

2️⃣ Before You Start

3️⃣ Wiring

4️⃣ Configure System

5️⃣ Pair Temperature Sensors (if required)

6️⃣ Commissioning the System

7️⃣ Installing the Wi-Fi Smart Hub

C43# KIT CONTENTS

1x C225: CPU

1x CT24ACE: 24v Power Supply

1x CFC12S: 12m Cat5e Cable

1x CCTSL#: Nexus or Nexus+ Touch Screen

1x C325#: AC Unit Interface (Brand Specific)

1x COCB: Smart Hub (Optional Extra)

1x CEXT: Zone Extender (Optional Extra)

1x CDTS: In-Duct Temperature Sensor (Optional Extra)

1x CR: Repeater (Optional Extra)

#x CRFS#: Wireless Temperate Sensors (Optional Extra and Number Supplied)

GENERAL INSTALLATION GUIDE

1️⃣ The C225, C325# and CEXT can be installed close to the indoor fan coil unit

2️⃣ If any wireless sensor (CRFS#) or wireless bridge (COCB) is not within the range of the C225 then additional repeaters (CR) should be added to help relay the signal from the field device to the C225 and the bridge

3️⃣ Do not run the cat5e cables alongside 240 Volt wiring

4️⃣ When installing network cables down wall cavities or chasing network cables into walls, tape up and protect the RJ45 connector to avoid damage to the connectors

Installation damage to cables is not covered under warranty

5️⃣ Always install zones in consecutive ports starting at Zone number one (1)

The C225 and CEXT are marked with the zone port numbers

6️⃣ Do not directly hard wire the CT24ACE into the AC unit’s power supply

This may void the warranty as it will require an electrician in the event that a repair of the iZone power supply is required

7️⃣ Connect Zone Damper Actuators (CZDA) to the zone ports using the RJ12 cables as shown in the Wiring layout diagrams

8️⃣ Connect the Colour Touch Screens (CCTSL# or CCTSL#+) to the iZone Net ports using the RJ45 cables

If you are connecting more than 3 components requiring iZone Net ports to the system you will need to connect a Network Extension Module Kit (CNEMK)

9️⃣ If any zone is temperature controlled, connect an in Duct Temperature Sensor (CDTS) to the CDTS port

Install the sensor into the supply air duct upstream of all dampers, then secure the sensor in place by using reinforced aluminium tape

1️⃣ 0️⃣ When installing temperature controlled zones ensure the CCTSL# or sensor for the associated zone is installed in a location that is representative of the temperature in the room / zone

The sensor should be installed at approximately 1600mm above the floor and should not be subject to draughts, direct sunlight or heat from equipment such as computers, TV screens etc

The supply air outlets to this room must not blow conditioned air directly onto the sensors or touch screens

1️⃣ 1️⃣ Connect the AC unit control cable to the C225 / C325.

See AC unit wiring connection section for details - C325#: AC Unit Interface - Install Guides

This control cable must be a shielded cable and is not normally supplied by iZone

1️⃣ 2️⃣ The building must be fitted with a compatible Wi-Fi modem

For a list of approved and recommended modems - COCB - Smart Hub - Install Guide

1️⃣ 3️⃣ If connecting the iZone system to a Home Automation system use the Ethernet connection on the bridge - iZone API Integration - Install Guide

1️⃣ 4️⃣ Only connect the power supply to the CT24ACE port after all components have been connected

1️⃣ 5️⃣ Any existing or new air conditioning units that require modification or additional boards to facilitate the correct operation of the iZone system, is the responsibility of the installing contractor

WIRING DIAGRAM - iZONE 430 WITH 0-8 ZONES

WIRING DIAGRAM - iZONE 430 WITH 8-14 ZONES

WIRING DIAGRAM - iZONE 435 WITH 0-8 ZONES

WIRING DIAGRAM - iZONE 435 WITH 8-14 ZONES

  • No labels