CL5D, CL5B22 and CL5E27: Smart Downlight and Bulb - Install Guide
PAGE CONTENTS
PHOTO & DESCRIPTION
Zone RGB LED lights need to be paired to the iZone Bridge (COCB) to enable them to be controlled
Pairing can be done via the touch screen or the iZone Home App
Once paired a light can be grouped to other lights, switches, modules or they can be added to a Recipe for simple control logic
Pairing modules and switches is usually done manually by pressing the pairing button and at the same time pressing the pair button on the screen or app
Facia: 3 facia colours are available (White, Silver, Black)
Spring clips: Strong spring clips with rubber boots
Diffuser: Plastic diffuser
Aluminium body: The aluminium body is extremely durable and the cooling fins ensure the down light does not over heat and damage the electronics
Each light has an on board temperature sensor which is displayed on the screen and is used as a safety to prevent the light from overheating and failing prematurely
Antenna: A small antenna protrudes from the casing for wireless communications (Not shown in this image)
SPECIFICATIONS
Model numbers | CL5DB, CL5DS, and CL5DW |
Certification | AS/NZS 60598.2.2; AS/NZS 61347.2.13; C Tick N29007; IP44; IC-4; SAA |
Power supply | Input: 220 - 240VAC 66mA ~ 50Hz |
Connection | 2 Pin Australian GPO plug |
Transformer | Custom transformer included. Output: 25V DC ~ 280mA The driver supplied is SELV EQUIVALENT |
Power lead | 1.2 meters |
Power consumption | Maximum 9.0 Watts on full brightness (Cool white) Minimum 0.22 Watts in standby mode |
Brightness | Maximum 523.7 Lumens |
Efficiency | 36.5 Lumens / Watt (Cool White) |
Beam Angle | 88.9 |
Control frequency | 433 MHz |
Operating Temperature | -20oC to +50oC |
Environment | IP44 rated Suitable for indoor use only. Suitable for alfresco, porch and bathroom use. |
Rating
| Suitable for residential or commercial use in Australia and New Zealand. Used where air transfer is not permitted or not desired between living space and roof space (there will be no air transfer between spaces even if there is no insulation covering the luminaire). These luminaires have been tested to 90oC and will automatically reduce in brightness to prevent over temperature. |
Requirements | An iZone bridge (COCB) is required to control an iZone smart light |
Size & Weight | Height: 69 mm (51 mm without antenna cover) Diameter 109.6 mm Hole cut size: 90 mm Weight 154 g (excludes transformer and lead) |
DOWNLIGHT INSTALLATION
This product must be installed by a qualified licenced electrician in accordance with AS/NZ 3000:2007 Electrical installations
Please note: Accidental contact with live parts does not rely on the luminaire enclosure
Warning this product is not suitable for mounting on tubular material
Ensure power supply is isolated before starting any work
Ensure downlight is located with minimum clearances from combustible building material as shown below
Connect mains power cable
Rotate spring clips up and gently insert downlight into hole
Pair down light
PAIRING A DOWNLIGHT GUIDE
BEFORE YOU GET STARTED…
Ensure your iZone bridge is paired to your modem
Download the iZone Home App onto your smart device
Ensure your light is installed and wired
For the purposes of this manual reference to an iZone RGB light refers to either an iZone RGB light bulb or and iZone RGB Down light
Tip: If you want to group multiple lights together you can pair them simultaneously. If you want each light to be on its own pair them one at a time. You can also group individually paired lights later using the group functions
DOWNLIGHT PAIRING
iZone RGB Light: Typical iZone RGB light bulb or down light
Flashing Red: When powered the light will flash red. This indicates the light is in its factory default setting and waiting to be paired to the system
If it is not flashing red you will need to reset the light to its factory default setting
Press the pair icon: On the touch screen or App > press the pair icon to pair the red flashing light to the system
Typical pair icon: In the "Devices" section of the App or touch screen there will be a pair button as shown. When the iZone RGB light is flashing red press this button to pair the light to the system
iZone RGB light will change to green: The iZone RGB light will change from flashing red to green when it has been paired to system
New light will be named L#: The newly paired light will be prefixed with the letter L, followed by a the next available number. In this example it is L5. If multiple lights are paired at the same time they will be shown as a single light
Indicates the light is turned on: The switch position indicates this light is switched on
Indicates current brightness: The brightness is represented a percentage. In this example it is 100%
Indicates current colour: The small box indicates the colour this light is currently set to
Special Effect active: This column shows what special effect is set for this light
Factory Resetting the Light
How to Pair a Light to a New Bridge (When the Old Bridge is Dead)
Follow these steps to factory reset and pair an existing light to a new bridge:
You must perform the pairing action (Step 6) within a few seconds of turning the light back on
Step 1: Prepare for Pairing
Locate the 'Change Bridge' Option:
On Nexus or Nano controller: Go to Device Config > and select Change Bridge. Keep this screen open for next steps.
On Nova controller: Tap Menu > Settings > System ID Number > and select Change Bridge. Keep this screen open for next steps.
On the iZone Home app: Go to Menu > Account > System ID > and select Change Bridge. Keep this screen open for next steps.
Power Off the Light: Make sure the light is turned off at the physical wall switch.
Wait: Keep the light off for a minimum of 60 seconds.
Step 2: Factory Reset and Pair
Power On: Turn the light on at the physical wall switch. The light should immediately switch to a cool white colour.
Act Fast - Pair: As soon as you see the cool white color, immediately go to your controller/app and hit the Change Bridge option you located in Step 1.
Note: You only have a few seconds once the light is turned on to successfully initiate the factory reset/pairing sequence
Verify Reset: The light should start flashing red, indicating that it has been successfully factory reset and is now in pairing mode. It is now ready to connect to the new bridge.
Troubleshooting: Light Doesn't Go Cool White
If the light does not switch to a cool white color when you turn it back on (Step 4), follow these steps to prepare the light for the factory reset attempt:
Leave the light on for at least 15 minutes.
Turn the light off at the wall switch, and then power it on again.
Go back to Step 1 of the main instructions and follow all steps from the beginning.