CACRB: Roller Blinds - Install Guide




The Roller blind module is hard wired to the mains power and uses wireless RF for the control communication

This module is only suitable for locating indoors however, it can control blinds which have a suitable rating that are located outdoors or in wet areas


Roller Blind Motors - Important Please Read!

Please note there are many different blind motor brands, makes and models available, however only certain motors will work with the iZone Roller Blind Module

If the roller blinds are to be run in parallel (more than one blind operated by a single iZone roller blind module) the motors used must be suitable for parallel configuration

You can still operate them as a single blind by grouping the iZone roller blind modules in the configuration menu

Check with your roller blind supplier to ensure the motors you are using are correct

A list of compatible roller blind motors are listed below. This list is not comprehensive

Single blinds ( Non parallel operation)

Alpha WSS40

 ACMEDA Automate ML45

 Motolux 802133000 (MT35-6-28-240/50)

Multiple blinds ( Parallel operation of multiple blinds from a single iZone module)

Becker motors – Model P5-30-E12 Motor

 Motolux 802131000 (MT35P-6-28-240/50)

There are probably many more makes of blind motors that will work with the iZone module so please let us know if you successfully use a motor that is not listed above and we will add it to the appropriate section


Wireless antenna:

The wireless antenna should be screwed in tight and after installation it should point up

Manual Up / Down / Stop button:

To test the Roller Blind module you can press this manual button to toggle through Up, Down and Stop functions

Pair button:

To pair the Roller blind module to the system ensure there is power to the module> Press the pair button on the module > . At the same time press the pair button on the App or iZone touch screen. >The blue LED inside the module (close to the pair button) will flash rapidly to indicate the module is pairing to the system

Remove cover to expose terminals:

Remove the terminal cover to expose the wiring terminal. Wire in accordance with the wiring notation on printed on the top cover. There are also wiring restraint cable ties that should be used to restrain the wiring in place. This should only be done by and electrician

Mounting point:

There are two mounting points on the module to allow the module to be mounted to roof timbers


Model numbers



AS/NZS 61058 ;  C Tick  N29007;  

Power supply

Input: 220 - 240VAC 50Hz

Power consumption

Maximum  2.35 Watts switched on (no load connected)

Minimum 1.05 Watts switched off

Maximum connected load permitted

5 Amp


Hard wired

Control frequency

433 MHz

Operating Temperature

-20oC to +50oC


Suitable for indoor use only


An iZone bridge (COCB) is required to control an iZone Roller blind module

Size & Weight

Height: 150 mm (Excludes mounting lugs and antenna)

Width 85 mm

Depth 36 mm (Excludes Antenna)

Weight 220g

(Designed to fit through a standard 95mm diameter down light hole)


Must have 240V, 4 wire motors, with mechanical stops, and suitable for home automation


Switch the power off at the switchboard

Remove the Roller blind module from the packaging

Cut the circuit to the device being controller and terminate the wiring as indicated on the casing.

If the roller blinds being controlled are capable of being wired in parallel you may connect multiple blinds to a single roller blind module up to a maximum of 5 amps.

If the roller blinds being controlled are not capable of being wired in parallel you must connect one roller blind module to each blind

Test the blind control and switching using the manual UP/Down/Stop button on the module.


Pair the iZone Roller Blind module to the iZone Bridge by pressing the pair button on the Roller Blind Module and on the screen simultaneously



The blue LED adjacent to the pair button on the module will flash blue several times to indicate it is pairing


Name your Roller blind module on the screen or app

Set the mechanical maximum and minimum stops on each blind

Calibrate roller blind in the iZone roller blind set up.

Configure the roller blind position for all On / Off functions.

Group your roller blind to other devices or switches as required