iZone has designed interface boards for most major Air Conditioning brands
For queries about specific unit models please contact our Support Team
Phone - +61 8 6556 6415 (Press 2 for Support)
Email - supportdesk@izone.com.au
iZone does not take responsibility for installing units that are not listed below or if the AC unit manufactured date is older than 2016. Please advise the iZone parts supplier of the indoor or outdoor unit model to prevent the incompatibility issues.
QUICK LINKS
ACTRON
Actron Compatibility: Ultra Slim \ low profile series only
Current Firmware Version - 1.3
SERIES & kW | INDOOR | OUTDOOR |
Ultra Slim \ low profile series only | LRE-###AS | URC-###AS |
Can use RA, Zones, Master and RF as controlling sensor
Polarity is critical see below, for correct connection
Connect a shielded, 2 core, twisted pair control cable from the C225 / C325A to the X / Y in the fan coil unit. This cable and connector is supplied by iZone - CACUCM15
1️⃣ Indoor fan coil unit PCB
2️⃣ CN40: Connect to X and Y
3️⃣ C225 AC unit connector: Connect AC unit cable from fan coil to C225 as indicated
4️⃣ Polarity is critical: Make sure it is wired in accordance with these instructions on both the CN40 connector on the fan coil PCB and the C225 cable connector
5️⃣ Cable from CN40: Ensure the cable is shielded, 2 core, twisted pair. This cable is pre-terminated suitable for CN40 connector and is supplied by iZone
BRAEMAR
Braemar Compatibility: SDHV series inverter ducted, single phase units only
Current Firmware Version - 1.3
SERIES & kW | INDOOR | OUTDOOR |
SINGLE PHASE / 7kw - 16kw | SDHV##D1S | SCHV##D1S |
Can use RA as controlling sensor
Cannot use Zones, Master or RF as controlling sensor
Polarity is critical see below, for correct connection
Requires Braemar proprietary controller for setup
Connect the Braemar proprietary wired controller to the FCU PCB
Enter the service mode parameters
To enter Service Mode, power must be connected to the unit and proprietary wired controller, and the unit must be switched 'OFF' at the wall control. Follow the steps below and refer to the function and parameter setting table
3. As per the instructions set the sensor to return air for all modes
4. Set the iZone control setting
5. Set the required static pressure setting
6. Cycle the power to the AC unit
7. Connect a 2 core, twisted pair control cable from the C225 / C325B X / Y to CN1 in the fan coil unit
A connector and short cable has been provided with the C325B but will need to be extended
Service Mode Parameter Table | |||||
Function Display | Function Description | Parameter Display | Parameter Description | ||
0 | Temp sensor location
Ensure set to '01'
| 01 | Sensor at return air for all modes | ||
02 | Sensor at wired control for all modes | ||||
03 | Sensor at return air for cool, dry & fan modes, at wired control for heat mode | ||||
10 | iZone control
Ensure set to '01' | 00 | Standard control | ||
01 | iZone control setting | ||||
11 | Indoor fan power setting
Factory default '05' Adjust to suit installed static Low static = '01' High static = '09'
|
| ESP (Pa) | High Speed | Low Speed |
01 | 10 | 5 | 1 | ||
02 | 20 | 6 | 2 | ||
03 | 30 | 7 | 3 | ||
04 | 40 | 8 | 4 | ||
05 | 50 (default) | 9 | 5 | ||
06 | 75 | 10 | 6 | ||
07 | 100 | 11 | 7 | ||
08 | 150 | 12 | 8 | ||
09 | 200 | 13 | 9 | ||
1️⃣ Indoor fan coil unit PCB: Note connector CN1
2️⃣ Connector and short cable provided: Insert the connector and short cable (see image below) into the connector CN1. Note the correct polarity for X & Y. Polarity is critical
3️⃣ C225 AC unit connector: Connect AC unit cable from fan coil to C225 as indicated
4️⃣ Polarity is critical: Make sure it is wired in accordance with these instructions on both the CN1 connector on the fan coil PCB and the C225 cable connector
5️⃣ Cable from CN1: Connect a shielded, 2 core, twisted pair cable to the connector and short cable provided
CARRIER
CODE | SENSOR TYPE | CONNECTION |
RA, Zones, Master, RF | CN40 / Polarity Critical | |
SERIES & kW | INDOOR | OUTDOOR |
HIGH STATIC / 9kw - 16.5kw | 42SHDV### | 38SHDV### |
DAIKIN
CODE | SENSOR TYPE | CONNECTION |
RA, Zones, Master, RF | P1 - P2 / Polarity not critical | |
SERIES & kW | INDOOR | OUTDOOR |
PREMIUM INVERTER SINGLE PHASE / 7kw - 16kw | FDYA###AV1 | RZA###CV1 |
PREMIUM INVERTER SINGLE PHASE / 7kw - 16kw | FDYQ###AV1 | RZQ###CV1 |
PREMIUM INVERTER THREE PHASE / 20kw - 25kw | FDYQ###LCV1 | RZYQ##TY1 |
INVERTER SINGLE PHASE / 5kw - 16kw | FDYAN###AV1 | RZA###CV1 |
INVERTER SINGLE PHASE / 5kw - 16kw | FDYQN###AV1 | RZQ###CV1 |
INVERTER THREE PHASE / 7kw - 25kw | FDYAN###AV1 | RZA###CV1 |
INVERTER THREE PHASE / 7kw - 25kw | FDYQN###AV1 | RZQ###CV1 |
VRV | FXMQ###-PAVE |
FUJITSU
CODE | SENSOR TYPE | CONNECTION |
RA, Zones, Master, RF | ||
SERIES & kW | INDOOR | OUTDOOR |
ARTG Series Wiring: Connect AC control cable to 2 and 3 - Polarity IS Critical | ||
High Static Single Phase - Compact Outdoor | ARTG30LHTA ARTG36LHTA ARTG45LHTA | |
High Static Single Phase | ARTG30LHTA ARTG36LHTA ARTG45LHTA ARTG54LHTC | |
High Static Infinity Range - Single Phase ONLY | ARTG45LDTA (single phase) ARTG54LDTA (single phase) ARTG60LDTA (single phase) | |
High Static Three Phase | ARTC72LATU ARTC90LATU | |
ARTH Series Wiring: Connect AC control cable to Y2-Y3 and SW1 dip switch ON - Polarity IS Critical | ||
High Static Single Phase | ARTH60KHTA ( Single Phase ) | |
Standard Range | ARTH54KHTA (Single phase) | |
High Efficiency | ARTH60KHTB (Single phase) | |
GREE
CODE | SENSOR TYPE | CONNECTION |
RA Only | CN1 / Polarity Critical | |
Requires proprietary controller | ||
SERIES & kW | INDOOR | OUTDOOR |
Inverter ducted, single phase units only R410A gas type only | GUD###PHS/B-S | GUD###W/Nh B-S |
Gree are using the same model numbers for their new R32 Gas type units, we are not compatible with these units at this stage
HITACHI
CODE | SENSOR TYPE | CONNECTION |
RA, Zones, Master, RF | A - B / Polarity not critical | |
SERIES & kW | INDOOR | OUTDOOR |
RPI ### 1SQ | ||
RPI ### 2SQ |
HAIER
CODE | SENSOR TYPE | CONNECTION |
RA Only | A - B / Polarity Critical | |
Requires proprietary controller / Requires Interface board | ||
SERIES & kW | INDOOR | OUTDOOR |
ADH series only |
iZONE
CODE | SENSOR TYPE | CONNECTION |
RA, Zones, Master, RF | CN40 / Polarity Critical | |
SERIES & kW | INDOOR | OUTDOOR |
Single Phase - 7kw / 17kw | AD###-I | AD###-O |
KADEN
CODE | SENSOR TYPE | CONNECTION |
RA, Zones, Master, RF | CN40 / Polarity Critical | |
SERIES & kW | INDOOR | OUTDOOR |
Single Phase - 7kw / 17kw | KD### |
LG
CODE | SENSOR TYPE | CONNECTION |
RA, Zones, Master, RF | A - B / Polarity Critical | |
Requires Interface board | ||
SERIES & kW | INDOOR | OUTDOOR |
B##AWYN7G5 |
CODE | SENSOR TYPE | CONNECTION |
RA, Zones, Master, RF | LG Supplied connector / Polarity not Critical | |
SERIES & kW | INDOOR | OUTDOOR |
B##AWYN7G6 |
MITSUBISHI ELECTRIC
CODE | SENSOR TYPE | CONNECTION |
RA, Zones, Master, RF | A - B / Polarity not Critical | |
SERIES & kW | INDOOR | OUTDOOR |
10kw - 14kw | PEA-M##GAA | |
10kw - 14kw | PEA-M##HAA | |
10kw - 14kw | PEA-M##JAA | |
16kw | PEAM160HAAYKIT | |
18kw | PEAM180LAAYKIT | |
20/25kw | PEAM200/250YKIT |
MIDEA
CODE | SENSOR TYPE | CONNECTION |
RA, Zones, Master, RF | CN40 / Polarity Critical | |
SERIES & kW | INDOOR | OUTDOOR |
DUC series only |
MITSUBISHI HEAVY INDUSTRIES
CODE | SENSOR TYPE | CONNECTION |
RA, Zones, Master, RF | A - B / Polarity not Critical | |
SERIES & kW | INDOOR | OUTDOOR |
FDU Series | ||
FDUA Series | ||
FDUM Series | ||
KX Series |
Indoor models FDUA200VG, FDUA200VF and FDUA200VH are compatible.
PANASONIC
CODE | SENSOR TYPE | CONNECTION |
RA, Zones, Master, RF | R1 - R2 / Polarity not Critical | |
SERIES & kW | INDOOR | OUTDOOR |
S - series units | ||
Nano X high static ducted |
RINNAI
CODE | SENSOR TYPE | CONNECTION |
RA, Zones, Master, RF | CN40 / Polarity Critical | |
SERIES & kW | INDOOR | OUTDOOR |
DINLR XX Series only |
SAMSUNG
CODE | SENSOR TYPE | CONNECTION |
RA, Zones, Master, RF | F3 - F4 / Polarity Critical | |
SERIES & kW | INDOOR | OUTDOOR |
R410A Gas Type - 5kW to 14Kw | AC###HBHFKH/SA | |
CODE | SENSOR TYPE | CONNECTION |
RA, Zones, Master, RF | F3 - F4 / Polarity Critical | |
SERIES & kW | INDOOR | OUTDOOR |
R410A Gas Type - 16kW to 20Kw | AC###JNHFKH/SA | |
R32 - 5kw to 14kw | AC###TNHPKG/SA | |
TOSHIBA
CODE | SENSOR TYPE | CONNECTION |
RA, Zones, Master, RF | A - B / Polarity not Critical | |
SERIES & kW | INDOOR | OUTDOOR |
A series only / S-Net protocol | RAV-SMXXX 3DT | |
10kw - 16kw | RAV-GMXXXDTP-A | |
MMD-UP0271HP-E | ||
TEMPERZONE
CODE | SENSOR TYPE | CONNECTION |
RA, Zones, Master, RF | ||
SERIES & kW | INDOOR | OUTDOOR |
UC8 board or above |
Not Compatible - UC7 board
YORK
CODE | SENSOR TYPE | CONNECTION |
RA, Zones, Master, RF | CN40 / Polarity Critical | |
SERIES & kW | INDOOR | OUTDOOR |
6850018 | ||
6850038 | ||
6850048 |
UNIVERSAL
CODE | SENSOR TYPE | CONNECTION |
SERIES & kW | INDOOR | OUTDOOR |